Shenzhen Jitian Chemical Co., Ltd.

Focused on adhesive materials and adhesive applications
for more than 20 years

+86-755-88834518

PRODUCT CENTER

Your current location: Home > Products Center > Adhesive > Silica gel >

Liquid silicone rubber H1001
Application/Uses
Making molds for
1·Culural relic duplication, architectural decoration,
   statues.
2·Resin crafts, Gift,decorations,reproduction
3·Lighting ornaments, candles, glass,
   acrylic plastic toy industry
4·Plaster, Gypsum, Cement, Concrete decorations
5·Artificial stone
6·Model design, product exploitaion,etc
  • Description
  • Specification
  • Application/Uses
    Making molds for
    1·Culural relic duplication, architectural decoration,
       statues.
    2·Resin crafts, Gift,decorations,reproduction
    3·Lighting ornaments, candles, glass,
       acrylic plastic toy industry
    4·Plaster, Gypsum, Cement, Concrete decorations
    5·Artificial stone
    6·Model design, product exploitaion,etc
     
     
    Key Attributes
    1·Good characteristics of easy-operation
    2·Light viscosity and good flowability
    3·Low shrinkage
    4·Favorable tensile and tear strength
    5·High temperature resistance,
       Acid and alkali-resistance
    6·High duplication times
    7·Vulcanize at room temperature
    8·Easy for demoulding
    9·No smell, non-flammable, safe and reliable
    Product Describe
    H10 series is a kind of two part silicone rubber , Part A is a flowable liquid, part B is the catalyst. in addition cure with mixing ratio of 100:2, It can cure at room temperature as well as under heat . It’s mainly used for mold making. polyester resin, epoxy resin, polyurethane molding products, PU foam resin decorations and reproduction of handicrafts.
     
    Typical Properties
    ITEM A B
    Type H1001 A H1001 B
    Appearance translucent liquid yellow liquid
    Density ( g/cm3) 1.2±0.05 1±0.05
    Mixing Ratio A:B=100:2
    Viscosity 20000
    Pot Time (Min) 10min
    Curing time (Min) 60min
    Operate Temperature ( ℃) 25 ℃
    hardness, A 25-27
    Tensile Strength, (kgf/cm² ) 30-32
    Tear strength ( KN/M) 22-24
    Elongation 400-450%
    Shrinkage rate (%) 0.30%
    Shelf life (25℃) 12 month
     
    How to use
    Step one : Prepare and clean the prototype.
    You must make sure your original molds perfect.
     
    Step two : Mixing part A and part B evenly
    Take 100g of part A and add 2g of part B and mix the silicone rubber and curing agnet evenly.
     
    Step three : Vacuum pumping
    Without exception, this step takes less than 10 mimutes. Otherwise, it will cause cross linking reaction, and no more further steps will be available.
     
    Step four : Pouring cast or brushing cast
    After released the bubble, we can pour/brush the silicone rubber on the prototype.
     
    Pouring cast
    It is suitable for simple products with the smooth surface. Without any mold lines, which helps you save time and is easy for operation. Evenly and slowly pouring the mixed silicone rubber into the square frame. After the cross linking reaction and the silicone rubber turns dry, you can take the products out .Thus, the mold has been done.
     
    Brushing cast
    1.Evenly brush the mixed silicone rubber on the product which is covered with mold spray with a brush or a brush pen.
    2.After the cross linking reaction ( about 30 minutes), brush a second coat which can increase the tension and tear strength of the mold.
    3.Cover a glass cloth on it after another 30 minutes of a second cross linking reaction, and a brush pen or a brush to avoid any interstices.
    4.Cover a third cost
     
    The vulcanization rate of this series is closely related to the ambient temperature and humidity. The higher the temperature, the higher the humidity and the faster the vulcanization rate. The user can select a curing agent according to the weather conditions, and adjust the amount of the curing agent to obtain an appropriate vulcanization rate.
     
    Comments
    Properties reported here are typical of average lots. Jitian chemical makes no representation that the material in any particular shipment will confirm exactly to the values given.
     
    Packing:
    The standard package of series liquid silicone rubber is 25 KG/drum . (note : the product’s specs and packing can be customized according to requirements.)
     
    Storage:
    Keep container closed when not in use.
    Store in a tightly closed container. Store in a cool, dry , well-ventilated area away from incompatible substances.
     
    REMARK
    Jitian Chemical shall not be responsible for the use of this information, or of any product, method, or apparatus mentioned, and you must make your own determination of its suitability and completeness for your own use, for the protection of the enviroment , and for the health and safety of your employees and purchasers of your products. No warranty is made of the merchantability of fitness of any product and nothing herein waves any of the seller's conditions of sale.